Frosted window films are progressively growing popular in the decorative window film industry as a cost efficient means to replace actual frosted glass windows that are installed at a higher cost for privacy and beauty purposes. Our Sparkling Frost film series encompasses all of these qualities of traditional frosted window films and more. Thick, stable, and secure, the Sparkling Frost decorative film contains durable PVC material that gives strength to the film and keeps it intact. This particular window film provides a fun twist from traditional frosted films with a tint of color as well as shimmering glitter. Whether it is in the office, home, bathroom, or cafés, the Sparkling Frost window films will brighten up your atmosphere.

The Sparkling Frost series comes in Black, Blue, Gold, Mint, Rose, and White. Similar to our Frosted Matte films, the Sparkling Frost decorative film completely blurs and obscures the object behind when applied on a window at a distance from the object. Unlike the Frosted Matte films which come in three solid colors, however, the Sparkling Frost film shimmers from its glitters on top of any chosen color. When an object leans against the tinted window, the film becomes transparent, furthermore highlighting the sparkles sprinkled across the colored film. Matte films are perfect for atmospheres that desire higher concentration and calm. If you are, however, looking for fun and dazzle, then the Sparkling Frost glass film is for you.

Combined with a silver glisten, the Gold Sparkling Frost Decorative Window Film can enrich your atmosphere with the richness of a gold, metallic color.

How To Apply?

To get started, you'll need a few tools:

- Spray bottle with a liquid soap solution

- Plastc card squeegee

- Few paper towels (cotton cloth recommended)

- Sharp retractable knife

1. Before You Begin Applying: Use the spray bottle with a soap solution to fully wet the window to the point where drops of soapy water run down the glass. Next, scrape off all of the dirt that might be present using a razor of some sort that won't scratch the glass. Then, use the squeegee to wipe down the window and remove the remaining dirt. Remember to use A LOT of soap water as it is important that the window remains completely wet during the window film installation process. Don't try to install the film in direct sunlight or in a hot environment as your soap solution will dry up quickly.

2. Measure and Cut Film: If you aren't experienced with applying window film, it would be a good idea to start with smaller windows first. Measure the width & height of the glass surface and determine where you'd like the film, keeping about a 1/2" margin of film around the window frame. The cut film should be bigger than the edges of your frame.

3. Remove Backing/Liner: Window films have 2 components: the film and the clear liner (the backing). When removing the liner, first peel away its corner (preferably the top right or left corners) by attaching two pieces of tape firmly to the front and back sides of the film's corner. Then, pull them apart to separate a little portion of the liner from the film but don't remove the liner completely.

4. Wet Both Sides of Film and Window: As mentioned above, it is important to keep both the window film and the window completely wet with the soap solution during the installation process.

5. Apply Film on Glass: Place the adhesive side of the film gently on the glass. Cling the peeled corners of the film onto the respective corners of the window and adjust the film so that the edges line up. While you remove the rest of the liner, make sure that the parts of the film that are already on the window stay in its place (it might be better to have someone hold the film while removing the liner). As you carefully peel the liner away, generously spray the liquid solution on the exposed sticky side (the side that's in contact with the window) of the film. After the liner is removed, align all corners and edges so that the shape of the film completely matches that of the window. If, at any point, the film is stuck and not moving, you need to peel it off a little and add more soap water to the window.

6. Final Touches: Now using the plastic squeegee, start at the top of the window and work your way down. When you squeegee out the water particles and the air bubbles, start at the center of the window and move out towards the edges. Spraying water on the film's surface will make the process much easier. Large bubbles can be removed with the squeegee, but keep in mind that small ones smaller than 1/8" will disappear within a few days. If necessary, trim the edges of the film with a knife. Finally, clean the film with soap water. It may take a few days to dry and completely stick to the glass.