The Blind series incorporates white linear lines into clear window film and creates an illusion of vertical blinds surrounding your window. Typically hung in front of balcony windows, the vertical blinds serve to protect your interior from excessive sunlight and provide privacy from the passersby while still allowing some natural light to enter. With your choice of Blind Decorative Window Film you will be able to enjoy the functions of traditional vertical blinds as well as the benefits of glass window films.

Due to the adhesive nature of the film, you can express your creativity by aligning the lines in a certain direction as best fit. Horizontal, vertical, or diagonal, the Blind series guarantees to satisfy your taste. Move past the limitations of vertical blinds and explore your abundant options that come only with decorative window films; the Blind series looks great not only on balcony windows but also on any glass that may otherwise appear mundane. Satisfy your aesthetic needs as well as your physical needs.

The Mini Blind Decorative Window Film has thin white lines stretching down the entire roll of film. The thinness of the lines prioritizes décor and emboldens beauty. The transparent gap between the lines juxtaposed with the white lines of almost equal thickness substantially reveals the background and heightens your surrounding. Highly sensible and sophisticated, the Mini Blind glass film is sensitive to your taste and strives to fulfill your creative drive. Compare its strengths with those of other Blind films here:

• design pattern is exquisite, chic, stylish and modern
• beautifies interior as well as exterior
• partial concealment of background
• experimental and incredibly worthwhile
• apt for hallway, café, office, hotel, bathroom, personal room windows and more

If you are tired of dusting off your vertical blinds and separating each from clutter, the Blind series is for you as it will largely enhance your environment with order and neatness. All it ever needs is just one touch of installation and you can enjoy its efficiency without ever having to worry about tending to them.

How To Apply?

To get started, you'll need a few tools:

- Spray bottle with a liquid soap solution

- Plastc card squeegee

- Few paper towels (cotton cloth recommended)

- Sharp retractable knife

1. Before You Begin Applying: Use the spray bottle with a soap solution to fully wet the window to the point where drops of soapy water run down the glass. Next, scrape off all of the dirt that might be present using a razor of some sort that won't scratch the glass. Then, use the squeegee to wipe down the window and remove the remaining dirt. Remember to use A LOT of soap water as it is important that the window remains completely wet during the window film installation process. Don't try to install the film in direct sunlight or in a hot environment as your soap solution will dry up quickly.

2. Measure and Cut Film: If you aren't experienced with applying window film, it would be a good idea to start with smaller windows first. Measure the width & height of the glass surface and determine where you'd like the film, keeping about a 1/2" margin of film around the window frame. The cut film should be bigger than the edges of your frame.

3. Remove Backing/Liner: Window films have 2 components: the film and the clear liner (the backing). When removing the liner, first peel away its corner (preferably the top right or left corners) by attaching two pieces of tape firmly to the front and back sides of the film's corner. Then, pull them apart to separate a little portion of the liner from the film but don't remove the liner completely.

4. Wet Both Sides of Film and Window: As mentioned above, it is important to keep both the window film and the window completely wet with the soap solution during the installation process.

5. Apply Film on Glass: Place the adhesive side of the film gently on the glass. Cling the peeled corners of the film onto the respective corners of the window and adjust the film so that the edges line up. While you remove the rest of the liner, make sure that the parts of the film that are already on the window stay in its place (it might be better to have someone hold the film while removing the liner). As you carefully peel the liner away, generously spray the liquid solution on the exposed sticky side (the side that's in contact with the window) of the film. After the liner is removed, align all corners and edges so that the shape of the film completely matches that of the window. If, at any point, the film is stuck and not moving, you need to peel it off a little and add more soap water to the window.

6. Final Touches: Now using the plastic squeegee, start at the top of the window and work your way down. When you squeegee out the water particles and the air bubbles, start at the center of the window and move out towards the edges. Spraying water on the film's surface will make the process much easier. Large bubbles can be removed with the squeegee, but keep in mind that small ones smaller than 1/8" will disappear within a few days. If necessary, trim the edges of the film with a knife. Finally, clean the film with soap water. It may take a few days to dry and completely stick to the glass.